Technical Papers

High Temperature Service

(2010 – Industrial Heating) – Micro-Alloyed Heat-Resistant Alloy Reduces Costs, Not Performance

(2008 – Stainless Steel World) – Heat Resistant Alloys Selection and Failure Avoidance

(2008 – Industrial Heating) – Heat-Resistant Alloy Selection – The Importance of Microstructure Under Cycling Conditions

(2007 – Industrial Heating) – Understanding Various Factors that Reduce Heat-Resistant-Alloy Component Life

(2005 – NACE) – Case Histories on Successful Applications of Alloy RA 602CA UNS N06025 in High Temperature Environments

(2005 – NACE & Heat Processing) – Materials Selection Considerations for Thermal Process Equipment

(2005 – NACE) – Micro-Alloying Improves Resistance to High Temperature Environments

(2002 – Industrial Heating) – Nickel-Base Furnace Alloy Extends Maximum-Use Temperature

(2002 – NACE) – Combatting High Temperature Corrosion with Alloy RA 602CA (UNS N06025) in Various Environments and Industries

(1999 – Stainless Steel World) – Metal Dusting in the Heat Treating Industry

(1997 – ASM Heat Treat Show) – Wrought Heat Resisting Alloys Provide Cost Reductions

(1995 – Steel Magazine) – Added Life for Brazing Fixtures

(1995 – ASM International) – Oxidation Rates of Some Heat Resistant Alloys

(1993 – Heat Treating) – Heat Resistant Alloy Performance

(1992 – Industrial Heating) – Influence of Composition and Microstructure on Performance of Wrought Heat Resisting Alloys

(1990 – Heat Treating) – Neutral Salt Pot Alloy Life Maintenance is the Key

(1990 – NACE) – The Use of New Generation Stainless Steels in combustion Systems

(1986 – NACE) – Evaluation of Heat Resistant Alloys in Composite Fixtures

(1982 – Heat Treating) – How Alloy Selection Figures in Design of Radiant Tubes

(1982 – Metal Progress) – An Evaluation of Heat Resistant Alloy Furnace Components

(1979 – Industrial Heating) – Understanding Conditions that Affect Performance of Heat Resisting Alloys

(1974 – Metal Treating Magazine) – Wrought Heat Resisting Alloys Provide Cost Reduction

(1973 – Metal Progress) – Analyzing Belt Pin Failures

(1963 – Production Equipment Magazine) – Lower Cost Heat Treating

(1962 – Rolled Alloys) – Cracking in Type 309 High Temperature Fabrications and How to Combat

 

Corrosion Environments

(2016 – NACE) – The Detection of Alpha Prime in Duplex Stainless Steels

(2015 – Stainless Steel World) – Hydrogen Induced Stress Cracking (HISC) Resistance and Improvement Methods for Super Duplex Stainless Steels

(2015 – EDA) – Specifying and Securing Quality in Procurement Manufacture and Fabrication of Duplex and Super Duplex Stainless Steel Parts for SWRO Applications

(2015 – NACE) – The Effect of Copper on Crevice Corrosion of Stainless Steels

(2014 – Rolled Alloys) – Optimisation of the Corrosion Resistance of Pipe Butt Welds in Super Duplex Stainless Steels

(2014 – TAPPI) – Impact of Availability and Economics on Alloy Selection

(2014 – NACE) – Corrosion Management of Assets Constructed in Super Duplex Stainless Steels Topside and Subsea

(2014 – NACE) – Availability and Economics of Using Duplex Stainless Steels

(2013 – OTC Brazil) – ZERON 100 (S32760), Advanced Forging Process (AFPTM), Super Duplex for Increased Low Temperature Impact Toughness and Resistance to Hydrogen Induced Stress Corrosion Cracking (HISCC)

(2012 – SPE International) – Duplex And Super Duplex Stainless Steels And Their Application In Steam Assisted Gravity Drainage

(2012 – Rolled Alloys) – Materials Selection for Membrane Plants Handling

(2011 – IDA) – Fabrication of Super Duplex Stainless Steel for Optimum Sea Water Corrosion Resistance

(2011 – NACE) – The Corrosion Of Super Duplex Stainless Steel

(2010 – Sulfuric Acid Today) – The Corrosion Resistance of Stainless Steels in Sulfuric Acid Plants

(2010 – NACE) – Super Austenitic Alloy N08367 Service Water Piping Review

(2009 – Stainless Steel World) – The Performance of Stainless Steels in Concentrated Sulfuric Acid

(2009 – NACE) – Use Of An Internal Corrosion Threat Assessment

(2009 – IDA) – Electrochemical Potential and the Corrosion Resistance of Stainless Steels in SWRO Applications

(2009 – Conference of Metallurgists) – A Review of Experiences With AL-6XN and Zeron 100 in Air Pollution Control Equipment

(2009 – IDA) – Field Experiences and Fabrication Techniques Related to AL-6XN Alloy for SWRO Applications

(2009 – AIRPOL) – Zeron 100 Super Duplex Stainless Steel for Wet FGD Air Pollution Control Systems

(2008 – Stainless Steel World) – Duplex Stainless Steels A Cost Effective Option for Biofuel Facilities

(2007 – NACE) – Factors Affecting Gasket Selection For Stainless Steels In Seawater

(2007 – AIRPOL) – AL-6XN Alloy Superaustenitic Stainless Steel for Air Pollution Control Equipment

(2006 – NACE) – The Performance Of Zeron 100 (UNS s32760) Super Duplex Stainless Steel

(2004 – Corrosion 2004) – The Selection Of Super Duplex Stainless Steel

(2003 – Powergen) – Al-6XN Alloy Of The 21St Century For Pollution Control

(2003 – NACE) – Experiences With Super Duplex Stainless Steel In Seawater

(1999 – Stainless Steel World) – Experiences with Zeron 100 Superduplex Stainless Steel in the Process Industry

(1999 – NACE) – The Corrosion Of Some Stainless Steels In Marine Mud

(1998 – Corrosion 98) – Molecular Monitoring Of Residual Corrosion Inhibitor Actives In Oilfield Fluids

(1998 – Corrosion 98) – Applications And Experiences With Super Duplex Stainless Steel In Web FGD Scrubber Systems

(1997 – Corrosion 97) – The Role Of Environment And Metallurgical Variables On The Resistance Of Duplex Stainless Steels To Sulphide SCC

(1994 – Interphex – USA) – Considerations in Selecting A Stainless Steel for Bioprocess Equipment

(1994 – The Institute of Materials) – Galvanic Corrosion of High Alloy Stainless Steels in Sea Water

(1994 – TWI) – Advantages of hot isostatic pressing (HIP) production routes for process manifolds